Ceremonial Leia Dress

This is for the dress Princess Leia wears when she presents Luke and Han their medals at the end of “A New Hope”. The dress is a floor length A-line dress, lined, and has a short train at the back. The ‘sleeves’ are open and fall to the floor, often being referred to as “wings”. And this is a good costume for plus size women.

Measurements 

You will need good measurements of yourself to get a proper fit. Have a friend measure you. And keep those handy for the dress making process.

Pattern 

If you are not an experienced seamstress, it would be helpful to start with a commercial pattern. The ideal one will have an empire waist seam (a seam just under the bust), round neckline, and no sleeves. No pattern will be perfect, so choose one that is as close as you can get. Be sure to check the measurements on the back of the package, and pick the size that will best fit you.

Example - This pattern has all the basic requirements; and with just a few alterations, will be screen accurate.

Fabric 
Beyond being white, the fabric needs to be a bit sheer (enough to see your hand under one layer), have a soft, flowing hand, and be washable as you are sure to get dirt on it as you wear it. One excellent fabric is the JetSet Poly typically used for the Senatorial Gown. But other fabrics such as swimsuit lining also make good fabrics for this costume.

Getting started – making a pattern and mock-up
You can make a copy of your pattern by laying tissue paper over the pattern, then tracing the pattern onto the tissue. This will give you a copy you can cut and alter as needed. Not only will you need to alter the pattern to fit you, but you’ll need to include a side zipper (on the wearers left side), you may need to add a train, lower the neckline, thin the shoulder straps, add/adjust darts for fitting, alter the bust seam, etc… this is why a copy is very handy, so you will always have your original pattern to go back to.

When your ready… cut a practice dress out, use an inexpensive fabric like muslin. Sew it together, and try it on. 

Use an inexpensive fabric for a mock-up first.

Specific Alterations

Bodice Front - Darts
You will probably need darts on the bottom layer in the front to help the dress fit to you. Be sure to include these in your practice dress, and alter as needed. These will be on the top layer and your lining layer. The ‘wings’ pieces will go over these and hide them.

Bodice Back - Darts
You will probably need darts in the back to help the dress fit to you. Be sure to include these in your practice dress, and alter as needed. These will be on the top layer and your lining layer.

Bodice Front - The ‘inverted V’ seam
This isn’t really a fold in the front bodice, but the place where the two bodice pieces meet, and the edge of the top layer creates this ‘seam’. You can accomplish this by shaping your bodice/wing piece to go beyond the center front, on an angle, and fold under at the edge. You’ll first stitch down the bodice/wing piece, fold it over, then sew it into the neckline on the top and the skirt on the bottom.

(click to enlarge)

The ‘wings’ - Front
For the shape at the bottom of the wing... it will be straight from the side seams down to about your knee. That is where the “flutter” part starts. (Letter A) The “flutter” part ends at the bottom of the wing, which should be the same length as your finished dress. (Letter B)

The ‘wings’ - Back
On the back, the ‘wings’ will go over your shoulder, and fall straight down to the hem of your dress.  

They will cover your shoulder, but not go across your back.  

And are left unstitched in the back. You can tell that when Leia reaches forward and part of her shoulder is exposed. (If you do have very round shoulders, and you find that your sleeves are always falling forward on you, you can hide a few hand stitches on the back of your shoulder to keep everything in place. Just be sure you can still reach forward with out the fabric pulling.)

A finished “wing” piece should look something like this:

(click to enlarge)

Facings –
You will need to make facings for the neckline, armholes, and hems. These are basically a 2 inch wide (2” unfinished, about 1.5” finished) piece of fabric used to finish the edges of the neckline, armholes, and the bottom hem. You can re-trace your neckline/arm holes/hems onto tissue and use a ruler to make matching curves 2 inches away from the first marks. The ‘inside edge’ will match to your dress, while the ‘outside edge’ will need to be finished off and tacked down. This will give all your edges a nice, clean, and comfortable finish.

The train -
Is a nice rounded sweep to the bottom of the skirt back. The longest part will be at the center back, and sweeping up to the side seam. 

Fitting –
Have a friend experienced in fitting garments fit your mock-up to you. This is the time to work on everything to get the fit and the alterations just right. You don’t want any surprises once you use your final fabric!

The real deal!
Once you have your mock-up completely adjusted, take it apart and use it as a pattern to cut out your final fabric. And assemble this way...


Sew the darts in the front and back pieces of the bodice. Baste together your lining and top pieces along the neckline, bust seam, and side seams. This will make it easier to handle them as one piece.


Lay the wing pieces on top of your bodice front, and use a dress makers pencil to mark where you need to stitch. Allowing for turning under the raw edge. Do this for both wings. 

Starting with the left wing, sew down the wing. Remember to place the wing with right sides of the fabric together, and that you’re going to fold the piece over the stitching.

Fold the wing over and baste along the neckline and bottom bust seam. Remember not to sew along the bust seam all the way to the side seam at the edge. You’ll need to leave ⅝ inch unattached so you can sew the side seam later.

Then repeat with the right wing.

Fold the wing over and baste down the neckline and bust seam.

      
Now you can add the skirt; join the front to the back; put in your neck and armhole facings. Remember, before finishing, you’ll need to do a little hand stitching at the side seams. Simply fold up about ⅝ inch of the wing and stitch it at the side seam on each side. (They are not stitched anywhere around the armhole.)

To finish off the costume, you’ll need to make a hairpiece (or use your own), necklace, bracelet, belt, and shoes.  

Written by Deidra Culp, Beret Balestrieri Kohn and Beth Thornton.
Illistrations by Deidra Culp and Beret Balestrieri Kohn.
Making-of photos by Beth Thornton.